Itw-linx DL1200-235 User Manual download pdf

1. Remove all plugs from the jacks in the protector

2. Remove (2) front screws marked “T

ray Release”.

3. Slide tray out from back of the protector

4. Remove punchdown wires on effected module (s).

5. Remove (2) screws on module.

6. Remove module and insert new module.

7. Attach (2) screws and punchdown wires in proper location.

8. Slide tray into chassis and fasten with (2) screws.

9. Insert plugs into proper jack locations.

CAUTION:

1. Never install telephone wiring during a lightning storm.

Disconnect telephone lines before installing protector

3. Protector and equipment ground should be connected to a single common ground.

4. Make sure no electrical surges are on the lines when installing or removing circuit cards.

5. The protector shall be installed in accordance with the applicable requirements of the

National Electric Code, ANSI/NFP

A-70, Article 800, Section C.

Thank you for choosing ITW Linx DataLinx® 1200. The

DataLinx 1200 will provide the finest surge protection

available for Power Over Ethernet (POE), Voice Over

Internet Protocol (VOIP) and LAN needs.

INSTALLING DATALINX 1200 SERIES UNITS

Using four standard rack mounting screws (included)

mount DataLinx 1200 to a standard 19" rack cabinet.

Detach the two front panel screws. Pull the back of the

housing out to expose the 110 connectors. Carefully

punch-down input pairs, maintaining proper wire twist.

Wires must be 24 AWG and be punched-down in

ompliance with either TIA 568-A or 568-B standards.

See diagram below.

WIRING CONVENTIONS/DIAGRAM

DL1200 / DL1200-235

DL1200-POE

Position cable(s) into the cable exit slots on the back of

the housing. Position and secure a cable tie on each

cable to provide strain relief next to cable exit slots in the

protector housing.

Push the housing back in and secure the two front panel

screws.

IMPORTANT: Attach a #6 AWG wire to the Screw

Ground Lug (SGL-1) on back of the unit to a properly

grounded Ground Bus Bar

To ensure Cat 5e performance, connect a Cat 5e or better

patch cord to the DataLinx protector and the equipment

to be protected. In the extremely unlikely event that

everything does not work perfectly, stop and read the

roubleshooting section. If you continue to have prob-

lems, call ITW Linx Customer Service Department at

DATALINX 1200 FEATURES

—Solid-state, Primary and

Isolated Loop protection, UL 497 and 497B, Cat 5e per

TIA 568-A and TIA 568-B)

ingle Height Chassis (1U)

Replaceable 4-port Modules

—In the event of a cata-

strophic surge you will not need to replace the entire

unit, just the modules that have been effected.

TROUBLESHOOTING

1. Intermittent or no LAN connections.

Wires are not completely punched-down or are not

punched-down correctly. Visually inspect for any lose or

on-connected wires. Verify that wires are punched-

down in compliance with either TIA 568-A or 568-B

standards.

OTE:

f system operating voltage exceeds the listed

initial clamping voltage for your unit or if a surge is

present on the network, the port will be connected to

GND by design. Remove surge source or check the

system voltage.

If you continue to have trouble with your DataLinx 1200

or this section has not fixed the problem, please call

ITW Linx Customer Service at:

CAUTION:

1. Never install telephone wiring during a lightning storm.

2. Disconnect telephone lines before installing protector.

. Protector and equipment ground should be connected to

a single common ground.

. Make sure no electrical surges are on the lines when installing

or removing circuit cards.

5. The protector shall be installed in accordance with the

pplicable requirements of the National Electric Code,

ANSI/NFPA-70, Article 800, Section C.

Note:

. Many old buildings are inadequately wired. It is very common

for a building to be improperly grounded. Building wiring and

rounding must conform to applicable NEC (USA) or CEC

(Canada). Ground impedance is recommended to be 1 ohm or

less. Protectors will not function properly when connected

improperly or to a faulty ground.

2. The DataLinx 1200 and the connected equipment must be

indoors and in the same building.

9026-040-00 Rev

. 3

DATALINX INSTALLATION INSTRUCTIONS

Models: DL1200, DL1200-POE, DL1200-75, DL1200-235

DATALINX REPLACEMENT CARD INSTALLATION INSTRUCTIONS

DL1200-RC-16, DL1200-RC-POE, DL1200-RC-75 and DL1200-RC-235

12 GND11109

LINE

87 6 5 43 21

DataLinx 1200

12 3456 78910 1112

TRAY RELEASE TRAY RELEASE

LINE

800-336-LINX • itwlinx.com

ool W

orks Inc.

™

FRONT PANEL—DataLinx 1200

12 GND11109

INE

87 6 5 43 21

DataLinx 1200

2 3456 78910 1112

RAY RELEASE TRAY RELEASE

INE

REAR PANEL—DataLinx 1200

W-O

W-G

W-BL

T568A

T568B

W-G

W-O

W-BL

W-BR

78364521

W-BR

W-O

W-G

W-BL

T568A

T568B

W-G

W-O

W-BL

W-BR

78364521

W-BR

ins 4, 5, 7 and 8 clamp at 62V,

Pins 1, 2, 3 and 6 clamp at 16V.

L1200—All pins clamp at 16V.

L1200-235—All pins clamp

t 235V

DL1200-75—All pins clamp

at 75V.

800-336-LINX • itwlinx.com 1

Summary of Contents

Page 1 - 800-336-LINX • itwlinx.com

1. Remove all plugs from the jacks in the protector.2. Remove (2) front screws marked “Tray Release”.3. Slide tray out from back of the protector.4. R

Related models: DL1200-75 | DL1200-POE | DL1200 |

Comments to this Manuals

No comments

Itw-linx DL1200-235 User Manual

Browse online or download User Manual for Routers Itw-linx DL1200-235. ITW Linx DL1200-235 User Manual

Summary of Contents

Related models: DL1200-75 | DL1200-POE | DL1200 |

Comments to this Manuals

Related products and manuals for Routers Itw-linx DL1200-235